Method C. Sounding rod depth required to hit the prostate.
I know it sounds odd to do this on a tree, but trust me, it works.
The question is, are we talking about a very normal cylinder? (possibly stuck to something?)
I measured like this when my first girlfriend asked what my size was. I told her it was 10". Suffice to say, she was definitely not impressed when the pants came off for the first time. ๐
I'll ask the branch manager.
What is your tree normally goes straight out with a cut l downward curve? The measurements are the same either way...
it took me way to long to realize y'all talking about penises ...
Half the length plus seven
here is an authority on the matter
https://m.youtube.com/watch?v=81bt0ZJLMas&pp=0gcJCUACo7VqN5tD&ra=m
Tear off the branch and measure the total length.
It is imperative that the branch not be damaged
It's just a branch who cares? Mangle that fucker lol
Ok chop down the tree and cut a line perpindicular to the bottom of the branch into the tree. Then measure the branch with watever remains of the tree attached.
Because it's oak-wilt season, right?
Unless you're into that
Probably from the side tbh as opposed to either of these two
Shine a light directly down on it from above. Measure the shadow
You have to push the branch down with one hand, such that it is perpendicular to the trunk. With the other hand place a ruler to measure trunk to tip via method A. This gives the honest expectation of ''usable" length.
Wrap the measuring tape until the entire branch is wrapped. For more accurate measurements, use thinner tape.
The only way to get an accurate measurement is to cut the branch off first.
It is imperative that the cylinder and the larger object remain unharmed.
"It's a meat cylinder"
The cylindet MUST stay intact!
I came here to say this. Take your stupid upvote.
Measure from the taint and add an extra inch to the measurement for standard wood shrinkage.
Method A on account that that would be the maximum usable length
Usable length is relative...
*reverse cowgirl enters the room, galloping backwards and surprising everyone*
As a skilled carpenter who's used to measuring wood, this is the only answer.
Well..... It kinda depends. If I were to be ordering stock to recreate the branch or even if I were making a covering for the branch. I'd have to order at least 6 inches of material to cut down.
So I think it matters most how you are intending to use it.
I would use 0,5x(A+B) because chicks dig a big branch.
Woah wait... Can we solve the measuring crisis but just measuring from the trunk at the top and all the way across then wrapping around the exposed end and back down the length on the bottom to the next obstruction?
Wouldnt that then include the width in your overall measurement and everyone would be generally impressed at any dimension?
The generally accepted method used by scientists is to firmly push your ruler against the base of tree at the top of the branch. This is called BPEL, or bark-pressed erect length.
What if there's a ... um ... protuberance on the bottom where the branch meets the trunk? What's the correct measuring procedure in that case?
It's critical the cylinder not be harmed
It's a perfectly normal cylinder size.
If you trim the bushes the branch looks bigger. Pro tip.
I just ask OP's mom.
I can't use method B, the tree fruit are in the way.
Welcome to Lemmy Shitpost. Here you can shitpost to your hearts content.
Anything and everything goes. Memes, Jokes, Vents and Banter. Though we still have to comply with lemmy.world instance rules. So behave!
1. Be Respectful
Refrain from using harmful language pertaining to a protected characteristic: e.g. race, gender, sexuality, disability or religion.
Refrain from being argumentative when responding or commenting to posts/replies. Personal attacks are not welcome here.
...
2. No Illegal Content
Content that violates the law. Any post/comment found to be in breach of common law will be removed and given to the authorities if required.
That means:
-No promoting violence/threats against any individuals
-No CSA content or Revenge Porn
-No sharing private/personal information (Doxxing)
...
3. No Spam
Posting the same post, no matter the intent is against the rules.
-If you have posted content, please refrain from re-posting said content within this community.
-Do not spam posts with intent to harass, annoy, bully, advertise, scam or harm this community.
-No posting Scams/Advertisements/Phishing Links/IP Grabbers
-No Bots, Bots will be banned from the community.
...
4. No Porn/Explicit
Content
-Do not post explicit content. Lemmy.World is not the instance for NSFW content.
-Do not post Gore or Shock Content.
...
5. No Enciting Harassment,
Brigading, Doxxing or Witch Hunts
-Do not Brigade other Communities
-No calls to action against other communities/users within Lemmy or outside of Lemmy.
-No Witch Hunts against users/communities.
-No content that harasses members within or outside of the community.
...
6. NSFW should be behind NSFW tags.
-Content that is NSFW should be behind NSFW tags.
-Content that might be distressing should be kept behind NSFW tags.
...
If you see content that is a breach of the rules, please flag and report the comment and a moderator will take action where they can.
Also check out:
Partnered Communities:
1.Memes
10.LinuxMemes (Linux themed memes)
Reach out to
All communities included on the sidebar are to be made in compliance with the instance rules. Striker
