Duck non-stick.

Treated myself to Le Creuset and will probably never have to buy something again lol.

Cast iron is pretty good at almost everything, but isn't the best at anything.

For searing meat at high temps, I've settled on stainless steel. It's easy to clean and maintain, and the typical 3-ply or 5-ply cladding has much better heat transfer characteristics than cast iron (which is a mediocre heat conductor masked by the fact that it's so heavy and thick that it takes on a lot of thermal mass to aid in searing). You don't have to worry about metal utensils or harsh scrubbers scratching the surface. And you don't have to worry about acidic ingredients messing with the surface, either.

For things that need nonstick characteristics, like eggs, I cycle through nonstick on a short replacement cycle (once every 2 or 3 years). I might get a carbon steel one day but I'm not in a hurry.

Cast iron is great if you use it a lot. It does take a little more work to maintain because after you clean it it's best if you dry it and coat it with a thin layer of oil, but you don't have to if you use it all the time. Mine is non stick enough to fry an egg with no oil, so it's better than my old ass Teflon pans in that sense, but probably not as good as a new Teflon pan

A good quality stainless set is far superior imho, you can actually keep it clean and dont have to mess around with seasoning it. Also, if you drop it, it won't break your foot and/or flooring. Cast iron is a fad that frankly is already dying out.

I have Lodge cast-iron skillets, Le Creuset and Staub ceramic-coated cast-iron dutch ovens, Le Creuset stainless saucepans, and one non-stick frying pan (which I bought for my wife).

I use the skillets for pretty much everything that isn't going to be simmered in tomato. Had them for years and they are non-stick. I happily fry eggs in them with no worries whatsoever.

Nah, honestly, any more than you need to backwards breathe to enjoy wine

Consumer reports does a non-stick pan test where they fry an egg without oil repeatedly until it starts to stick. The point is that normal use degrades non stick surfaces, so every non-stick pan, no matter how fancy, will one day be garbage.

Don't get me wrong, I use both non-stick and metal surface pans. I think they both have their place, but I think of non-stick pans as expendable.

I don't like non-stick anymore because the coating eventually gets all scratched up and doesn't work as good. Idk how it gets scratched up, I never used metal. My ex did, so maybe it was her.

Cast Iron, if maintained well (i.e just don't cook anything too acidic. You don't usually need to re-season), lasts forever. It's also great for when you want to sear something without the pan cooling down once you put your food on it. Because it's thick and stores a bunch of heat. Yet somehow it also gets hot pretty fast.

I don't get stainless steel personally. Apparently to get things to not stick, I should be using MORE heat? But I already use a lot of heat! On the up side, they get hot really fast.

Copper and carbon steel I've never used. I hear carbon steel is similar to cast iron in many ways, but easier to maintain?

If you're doing a new build, definitely go induction. Electric sucks because it's kinda slow-ish to get started, gas sucks because either you need to have a gas line built to your house if you don't already have one, or you change out the gas container every now and then (and that thing is heavy, mine's 17 KG of gas + whatever the huge chunk of metal weighs, which is definitely more than 17 KG). Plus the whole issue of, y'know, freshly burnt hydrocarbons (yay CO2 and potentially other gases). Oh and gas explosions aren't common, but they can happen!

Only downside of induction is that if you lose power, you can't cook. A wood-burning stove as a backup is excellent in this case, because depending on what your heating system is, you may also lose heating if power is gone.

Induction gives you the speed and control of gas, without the exhaust gases. Induction is more efficient than infrared, because you're heating the pan directly. The cooktop only gets hot from the pan resting on it.

Get induction, it's by far the best!

Cast iron flavors the dish some. A seasoned one adds the oils and other stuff used to season it as well.

Non-stick chemicals have been historically poisonous, don't know about the modern stuff though.

Also, cooking with cast iron increases iron intake.

Yes. Our house only has cast iron and stainless.

There's a small learning curve with cast iron, but the less you worry and over think it, the easier it gets. I fry eggs every other day in mine, and it's about as non-stick as anything else. Preheat the pan or griddle, that's all. Cleanup is a wipe with a paper towel or a rinse and quick scrub.

Cast iron works 95% of the time, but acid can strip the seasoning. So anything simmered an hour or more in tomato or win,e or sauted with lemon juice, get stainless. Don't put it in the dish washer. Not a lot of rules, really. My pan is 15 years old. My Mom uses ones that might be older than her.

When I travel and have to use someone else's non-stick pans, I hate the delicate little snowflake pieces of shit. Flimsy, toxic, someone else showed it a fork once so now it has damage and sticks anyway in a line across the middle, can't go on the oven, can't sear, handles all wobbly. Generally just disposable trash. Why would you love trash?

It lasts forever, you wont scrape whatever "non-stick coating" they use off. If you want a pan that will outlive your grandchildren and is permanently non-stick once it's seasoned, for most things a cast iron is perfect. If you have that, some pots of various sizes, and a wok, youre set.

I prefer induction or infrared stovetop. We dont need to burn more gas.

The reason cast iron is useful for searing a big cut of meat is that it has a reasonably high specific heat capacity (less than aluminum, more than copper, similar to steel) combined with considerably more mass than typical cookware made of other materials. It takes longer for the meat to cool the pan, so more heat transfers into the outer surface of the meat.

Cleanup of properly seasoned cast iron should be about as easy as non-stick pans because the seasoning (polymerized cooking oil) is, in fact a non-stick surface. Contrary to popular belief, it's fine to use soap on it, but aggressive abrasives can strip the seasoning. Fortunately, that's not hard to fix.

I like carbon steel, mainly for two reasons

1. Heats up insanely fast
2. Super easy to clean

No

Induction FTW and cast iron does work the best with induction since it heats up the most. However, I also enjoy non-stick since it being slower is an OK trade-off for the easy cleanup

Cast iron is overrated. And people overthink a lot about it being seasoned. Really though, you still have to care for it and it isn't like you can just re-season the pan. Just make sure it doesn't rust.