23
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
this post was submitted on 19 Jul 2023
23 points (100.0% liked)
3DPrinting
15525 readers
91 users here now
3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io
There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml
Rules
-
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
-
Be respectful, especially when disagreeing. Everyone should feel welcome here.
-
No porn (NSFW prints are acceptable but must be marked NSFW)
-
No Ads / Spamming / Guerrilla Marketing
-
Do not create links to reddit
-
If you see an issue please flag it
-
No guns
-
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
founded 1 year ago
MODERATORS
I'm not massively experienced with 3D printing so take this with a grain of salt.
That said though, I would personally consider what you would be doing in the future: If you're just going to use it occasionally for small projects then it probably isn't worth spending more than about 300€, but if you're likely to use it a lot and eventually start to print more complex / intricate things and/or more often then getting a slightly nicer one would end up being worth it in my opinion!
Personally I have an Anet A8 (about 200€), it's very basic and needs a lot of manual fiddling. Fortunately though, with a bit of tweaking in a slicer, it can produce quite nice prints in a reasonable time which is just fine for me as I only print infrequently and mostly things that don't need to be too precise. There might be something better for that price point but if you're just looking for something cheap that gets the job done then it'd probably serve you well!
My Anet A8 lacked the aluminum bracket to which the extruder is mounted. Luckily I got refunded in total, got a friend to print me an E3dv6 carriage and went with bowden setup. I haven't had but problems with that printer, I spent more time fixing it rather than using it in the past two/three years. There is always something not working, something about to break, something to be repaired. The board and the heated bed are an heat hazard, I've personally seen a friend's a8 coming with an extruder which would clog every couple minutes. The frame is not stiff and vibrates a lot, the stock carriage is barely held up by the two z axis motors, weighs a ton and often unalligns itself during the print. Different extruders would randomly clog even with esteps and flow calibrated and no heat creep.
I got mine for 100€ and got refunded in total because a crucial piece was missing, but for 200€ you're better off waiting for a nice offer on a ender 3. I wouldn't recommended thatprinter to my worst enemy.
Also nice that my first lemmy comment is me crapping on my anet a8.
Disclaimer: Don't buy an Anet A8 as a beginner!
Once the Anet A8 is fixed it's a respectable machine. I am always surprised to see their print quality (800mm^2/s acceleration). What made a major difference for me was bolting the A8 down to wood.
Fair enough, i guess being that cheap it's like many things - a roulette wheel of quality. Probably one of those things where I haven't used anything else so don't know what's good and what isn't!
Glad i recommended taking my judgement with a pinch of salt.