1475
Binary search
(slrpnk.net)
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
this post was submitted on 02 Dec 2024
1475 points (100.0% liked)
Memes
8573 readers
360 users here now
Post memes here.
A meme is an idea, behavior, or style that spreads by means of imitation from person to person within a culture and often carries symbolic meaning representing a particular phenomenon or theme.
An Internet meme or meme, is a cultural item that is spread via the Internet, often through social media platforms. The name is by the concept of memes proposed by Richard Dawkins in 1972. Internet memes can take various forms, such as images, videos, GIFs, and various other viral sensations.
- Wait at least 2 months before reposting
- No explicitly political content (about political figures, political events, elections and so on), !politicalmemes@lemmy.ca can be better place for that
- Use NSFW marking accordingly
Laittakaa meemejä tänne.
- Odota ainakin 2 kuukautta ennen meemin postaamista uudelleen
- Ei selkeän poliittista sisältöä (poliitikoista, poliittisista tapahtumista, vaaleista jne) parempi paikka esim. !politicalmemes@lemmy.ca
- Merkitse K18-sisältö tarpeen mukaan
founded 2 years ago
MODERATORS
Oh, well, you switch off half the fuses, then you go check the wire.
Let's say the wire still has power on it, so now you know that none of the fuses in that half affected it (which you can turn back on now).
Then you do the same thing again with the other half of the fuses, i.e. you switch off half of the fuses in that half and go check the wire.
Now, let's say the wire is dead, so now you know that the fuse you want is in this quarter.
So, then you flick off half of the fuses in that quarter and check the wire again, and so on.
With every step, you eliminate half of the remaining fuses, so for 60 fuses, you need at most 6 steps (which is the logarithm for base 2 of 60).
Once you figure out which one it is, label it! I labeled all the breakers in my panel when I moved in to my house, as half of the existing labels were wrong (no idea why).
That's the case with virtually every breaker box.
Why are so many mislabeled though? It's not like the loads are being changed every day. I had two breakers labeled "dishwasher" and neither of them were the dishwasher!
Electrical work is one of those things that's not difficult to do as long as you don't mind it being some level of wrong but relatively hard to do 100% to code right without training. With most of the wrong ways, the project still works, but it's dangerous and/or hard to maintain. Professional work is expensive, so you end up with a LOT of handyman work that's poorly labeled, poorly run, poorly designed or some combination of the three.
My best guess would be that at some point, running the dishwasher tripped the breaker. They had space so they added a breaker below it and moved the line to the new breaker. Then it still tripped, so they moved the line at the dishwasher circuit that was already close by.
Either the original line has a fault in it (old aluminum lines can have junction issues over time) or the dishwasher had a short in it, and they either replaced the dishwasher, or the new line they chose didn't fail.
I have only six circuits and both of my recent electricians checked and labelled each circuit. I must have had good luck in sparkies
What Rumba said. Why full ass a job when half is plenty.
I keep a spreadsheet with every outlet/light in every room on it and their corresponding breakers. Much easier since breakers often span multiple rooms, sometimes only powering one or two fixtures in each.
Ah, obvious now, thank you. For some reason ~~my~~ his brain couldn't get to actually turning off half the breakers in one go